PoliGlow - An End to Boat Wax

PoliGlow Does your boat shine when wet only to fade again once the water dries?

#1 Rated By Publication "Practical Sailor"
#1 Rated By "Power Boat Reports"
PoliGlow is NOT a Wax
PoliGlow is a clear-coat with a Gloss Level More Than 5 Times That of any Wax
Highest Initial Gloss of All Do-it-yourself Products Tested
Won Highest Gloss After 12 and 21 Months
PoliGlow is a New Concept in Boat Polish
PoliGlow will NOT wash off with regular boat soap cleaning (not even with compounds)
Easy to apply-Wipe on, No rubbing or Buffing
Lasts for over 12 months
Can Be Used on Boats, RV's, Travel Trailers, Airplanes, Trailers, or any Fiberglass Surfaces. (Not recommended for automobiles)
Not recommended for brand new boats (up to 2 years old) (for new boats, use the Four Seasons Boat Wax or the Collinite 885 Fleet Wax)

Introducing the PoliGlow System

Traditionally, boat waxes, cleaners, and compounds have been used to restore aged gelcoat. The problem is they wash away and don't last very long. Just ask anyone who has spent hours of breaking their back waxing only to have the surface return to it's aged look within a few months time.

As fiberglass ages, UV rays from the sun change the gelcoat finish - the surface becomes microscopically pitted so that light, instead of being reflected in one direction becomes scattered, reflecting back in random directions, creating a dull and faded appearance. The PoliGlow process first clears the microscopic voids of the collection of accumulated compounds, waxes, oxidation and grime; then the PoliGlow fills those voids and produces a "like wet" surface reflection superior to any wax available!

PoliGlow is not a wax, it is a protective clear coat that has been proven to have a shine 5 times that of the best waxes on the market. Not only that, but it also maintains that shine for up to a year and more. Say goodbye to buffing, PoliGlow is a different animal.

Don't take our word for it...

Practical Sailor & Powerboat Reports
Consumer Resource Publications for the U.S. Marine Industry

What did they conclude?

Highest Initial Gloss of All the "Do It Yourself" Products Tested Ease of Removal "Excellent" POLI GLOW is one of our favoritesRecommending Poli Glow is a no-brainer.

It all started in 1997 when PoliGlow achieved the highest gloss of any DIY (Do-It-Yourself) Hull Restorer.

Then top Honors In 1999: "Fiberglass Hull Restorers: 21 Month Report"

Again In 2004: "Our tester puts Poli Glow at the head of the pack."

Most Recently in 2007: "Recommending Poli Glow is a no-brainer."

Applying POLIGLOW

The surface does not need to be shiny for the application of PoliGlow, just clean and uniform in color. PoliPrep should be used to assure that the surface is clean, free of oxidation, wax and rubbing compounds, mildew, oil, or grease.

Preparation of surface is the most important step!

These very important steps should not be omitted. The final results will be based on this initial preparation. Clean surface thoroughly making sure it is free of stains, oxidation, dirt and previously applied wax, polish or rubbing compound. These products will interfere with the application of PoliGlow.

PoliPrep will remove oxidation, old wax, rubbing compounds, stains mildew, oil and grease. Wet the surface, then apply PoliPrep with a sprayer (always wear gloves). Scrub with supplied scrub pad until the surface feels smooth and is free of stains and oxidation. For severe oxidation, you can use a more abrasive scrub pad. Rinse the area with clear water and allow to dry thoroughly. You are now ready to apply PoliGlow.

Applying Poli Glow

For best results, apply to dry surface using our 7" applicator. For smaller, hard to reach areas, use our smaller applicator, which is included. Do not allow applicator to dry. Keep applicator soft by rinsing with clean water occasionally. Apply in thin, even, slightly overlapping strokes. Do not go over coats until dry. To keep surface clean, avoid windy conditions and apply in temperatures between 55 to 95 degrees F. PoliGlow can be applied in direct sunlight on light colors only. For easier application, apply in overlapping 5' square sections allowing each coat to dry (Approx.60 seconds). The first several coats may appear streaky due to the absorption of PoliGlow into the surface. A minimum of 5-6 coats will make the surface shine like new. Avoid contact with rain for several hours. Allow surface to cure for 24 hours before coming in contact with water.

Maintenance

PoliGlow is a unique product. It will not wash off or be affected by soap and water. A mild soap will keep your surface shining and clean. To maintain a PoliGlow shine, reapply one or two coats every 6-8 months. Avoid contact with ammonia-based products, degreasers, teak or hull cleaners and abrasive cleaning products. PoliPrep will easily remove PoliGlow. Spray on small area, let stand 1-2 minutes (do not allow to dry), scrub with the scrub pad. Rinse area with clean water.

Guarantee

If you are not totally satisfied with PoliGlow, return unused portion, with a copy of your receipt, within 12 months for a full refund.